Top-Rated HVAC & Water Heater Services in Belleville

Responded to no heat call on boiler system. Diagnosed faulty automatic vent damper preventing proper operation. Replaced defective Fieldcontrols motorized vent damper with new unit, restored system to normal operation, and verified proper venting and burner ignition sequence.

Completed scheduled heating maintenance visit as part of comfort club agreement with no active problems reported. Performed comprehensive system tune-up including diagnostic testing of electrical components using Fieldpiece meters, measuring voltage and amperage readings at multiple test points throughout the unit. Inspected internal components including blower motor assembly, capacitors, control board, contactors, and all electrical connections and wiring harnesses to ensure proper system operation for the upcoming heating season.

Completed installation of WiFi module to KOHLER residential standby generator. Established electrical connections between generator control panel and WiFi interface module using appropriate conduit and wiring methods. Configured wireless connectivity to enable remote monitoring and control capabilities. Verified proper module operation and communication with generator control system. All connections secured per manufacturer specifications and applicable electrical codes.

Completed preventative maintenance tune-up on Goodman DGFPA048ST1 gas furnace unit. Performed standard system inspection, verified AHRI certification specifications, checked air flow through supply vents, and documented equipment condition with photos of unit data plate and vent assembly.

Completed Club Heat 12-4 agreement visit for air handler and system inspection. Performed routine maintenance including removal and cleaning of burner assemblies, inspected all components for wear and proper operation. Cleaned and reinstalled air filter. System tested and operating within normal parameters upon completion.

Completed preventative maintenance inspection on residential outdoor air conditioning unit as part of Club AC8-12 agreement. Performed comprehensive system evaluation including visual inspection of condenser unit exterior, electrical components, capacitor, contactor, and wiring connections. All electrical connections found secure with proper color-coded wiring intact. Capacitor and contactor operating within normal parameters. Unit exterior showing typical environmental weathering with dirt and mineral deposit accumulation on casing. Condenser coils and fins accessible through top opening appear functional with age-appropriate darkening. System mounted securely on concrete pad with no structural concerns noted. Equipment photographed for service records documenting current condition of exterior cabinet and internal electrical compartment components.

Completed scheduled HVAC maintenance agreement visit for tune-up service on residential air conditioning system with no reported issues. Upon arrival, found outdoor condensing unit with heavily soiled condenser coil fins showing significant accumulation of dust, dirt, and environmental debris blocking airflow passages throughout the coil surface. Performed comprehensive system inspection and cleaning, including thorough condenser coil cleaning to remove buildup and restore proper airflow through fins. Verified unit operation and system performance following maintenance procedures. System restored to optimal operating condition with improved heat transfer efficiency.

# HVAC Furnace Installation Completed mechanical installation of residential furnace system. Installed new furnace unit and reconnected all necessary mechanical components including gas lines, electrical connections, and ductwork. Properly vented exhaust system through roof penetration using white PVC piping with appropriate flashing and weatherproof sealing to prevent water infiltration. Sealed all roof penetrations with rubber boot flashing and roofing sealant to ensure weathertight installation. Verified proper venting clearances and secure mounting of all exhaust components. System tested and operational upon completion.

Conducted comprehensive assessment of residential HVAC furnace system originally installed in 2002. Unit exhibited extensive deterioration throughout, including failing blower motor, heavily soiled blower wheel, deteriorating ignitor, out-of-specification blower capacitor, and heat exchanger in poor condition. Documented all component conditions with photographic evidence and provided detailed replacement estimate for complete system upgrade due to multiple failing components and overall unit deterioration.

Completed scheduled HVAC maintenance tune-up on air conditioning and air handler system as part of membership agreement benefits. Performed comprehensive system inspection, electrical diagnostics with multimeter showing 295V supply, verified blower motor operation, and assessed internal components including capacitor and control board functionality. Noted significant dust accumulation on blower motor assembly and surrounding cabinet areas with visible paint deterioration on motor housing; system operating within normal parameters with no immediate repairs required at time of service.

Completed full HVAC system installation including new Lennox condensing unit positioned on freshly poured concrete pad with proper leveling and clearances maintained per manufacturer specifications. All electrical connections, refrigerant lines, and drainage systems installed to code with system tested and verified operational upon completion.

Conducted estimate for complete HVAC system replacement after diagnosing failed outdoor condensing unit with overheating compressor experiencing lock-up condition and determining existing R-22 refrigerant system requires replacement due to obsolete refrigerant phase-out. Evaluated indoor vertical furnace and air handler assembly housed in closet configuration and outdoor cylindrical condensing unit, both showing age and wear, and provided replacement recommendations for full system upgrade to meet current efficiency standards and refrigerant regulations.

Conducted comprehensive site assessment for whole home generator installation. Evaluated existing electrical infrastructure, main service panel capacity, and optimal generator placement location. Documented electrical panel configuration, available space for automatic transfer switch installation, and natural gas or propane fuel source accessibility. Provided detailed estimate for 8-10 kW standby generator system including equipment, transfer switch, electrical connections, and installation requirements.

Completed mechanical-only boiler installation in residential utility space. Installed new boiler unit with comprehensive copper piping network, including supply and return lines, expansion tank, ball valves with shutoff capability, and all necessary brass fittings and connections. Reconnected existing electrical components to new system and secured all piping with proper wall brackets to ensure structural integrity and code compliance.

Conducted on-site evaluation for hot water boiler replacement estimate. Existing 30+ year old natural gas-fired boiler currently operational but scheduled for replacement due to age. System services hot water baseboard heating distribution. Assessed existing mechanical room infrastructure including copper supply and return piping, gas lines, and ductwork configuration. Documented wall-mounted thermostat and control system locations for replacement coordination.

# HVAC Maintenance Agreement Visit - Air Conditioner Tune-Up Completed Performed comprehensive preventive maintenance on residential air conditioning system as part of prepaid maintenance agreement. No operational issues or concerns reported prior to service visit. ## Work Performed Conducted complete air conditioner tune-up and inspection on indoor air handler unit located in basement mechanical room. Performed visual inspection of all accessible components including refrigerant line insulation, electrical connections, and condensate drainage system. Verified proper installation of vibration dampeners and flexible connectors on refrigerant lines. Inspected copper refrigerant piping with white insulation wrap secured with mounting straps for any signs of damage or deterioration. Examined manufacturer information plate and verified system specifications. Assessed condition of PVC condensate drain lines and fittings for proper drainage and potential blockages. Checked air handler cab

Completed warranty work for crawl space portion of HVAC installation. Performed system diagnostics using digital manifold gauge set, verifying refrigerant pressures at service ports on copper line set with proper brass fittings and insulated suction and liquid lines. Confirmed proper installation of air handler unit in mechanical space with complete condensate drainage system using PVC piping with appropriate primer application at all joints, condensate safety switch properly mounted and secured, and metal ductwork correctly installed with proper support strapping.

Successfully completed installation of a 2.5 ton air conditioning system with matching evaporator coil at residential property. Unit was positioned in rear yard location with electrical reconnection performed to code. All mechanical and electrical connections were secured, system was tested for proper operation, and site was left clean and ready for customer use.

Completed mechanical installation of 3-ton air conditioning system with matching evaporator coil in rear yard location. Installed new indoor air handler unit in basement mechanical room, connected refrigerant lines, established electrical connections, and mounted smart thermostat for system control.

Performed scheduled HVAC maintenance agreement visit for AC and system inspection. Upon inspection of the air handler unit, documented heavily soiled mesh filter media within the ductwork plenum showing significant accumulation of dust, debris, and particulate matter with dark streaking patterns. Verified integrity of reflective foil-faced duct insulation and vapor barrier. Photographed system conditions for maintenance records. System operational at time of departure.