Top-Rated HVAC & Water Heater Services in Belleville

Responded to no cooling complaint on Lennox unit model M296IUH070XV36B. Found evaporator coil frozen solid in air handler, indicating restricted airflow or low refrigerant charge. Documented equipment nameplate specifications and system condition upon arrival for service records.

Responded to service call for aging air conditioning system with inadequate cooling performance. Performed temporary repair by replacing failed capacitor and cleaning unit to restore limited functionality and provide immediate relief. Completed comprehensive assessment of existing HVAC system and provided estimate for full AC replacement due to advanced age and declining efficiency of current equipment.

# No Cooling After Power Outage - 5-Year-Old AC System Responded to a no cooling call on a 5-year-old residential air conditioning system that stopped cooling following a recent power outage. Upon arrival, confirmed the system was running but not producing cool air throughout the home. Performed a comprehensive system evaluation beginning with the indoor air handler unit. Inspected the blower assembly and confirmed the blower wheel was operational and rotating properly, though noted moderate dust accumulation on the blades that could impact airflow efficiency. Verified blower motor operation and mechanical components were functioning without unusual noise or binding. Proceeded with electrical diagnostics using a digital multimeter to test system voltages and capacitance values. Measured capacitor performance on the blower motor, recording readings of 0.75 MFD against manufacturer specifications. Tested electrical connections at the air handler, verifying proper voltage supply had be

Completed full HVAC system installation including a 70,000 BTU Lennox furnace, 3-ton Lennox air conditioning unit, and humidifier system. The outdoor AC unit was positioned on a concrete pad in the rear yard with proper electrical conduit installation and connection. Interior mechanical components were installed in the utility area with all necessary plumbing connections, PVC venting, and copper supply lines properly configured. All equipment was reconnected, tested for proper operation, and system commissioning was successfully completed.

Conducted on-site evaluation of existing air conditioning system for replacement estimate. Current unit is operational but of undetermined older age, located exterior to residence with natural gas furnace inside. Assessed electrical service panel, outdoor condenser unit positioning on concrete pad, disconnect box configuration, and existing refrigerant line routing to provide comprehensive replacement system recommendations.

Conducted on-site evaluation of existing outdoor air conditioning unit for replacement estimate. Unit exhibited significant weathering, mold growth, and exterior deterioration consistent with age, with manufacturing date confirmed as August 2013. Documented current system specifications and conditions through photographic assessment to provide accurate replacement recommendations.

Performed maintenance service on outdoor air conditioning condenser unit located in side yard against exterior brick wall. Removed top access panel to inspect internal components, including metal mesh filter screen, and checked for proper operation. Completed necessary adjustments and reassembled unit to restore normal cooling function.

Completed full HVAC system installation including a 110,000 BTU furnace and 4-ton air conditioning unit with outdoor condenser positioned on right side of property. Performed all mechanical and electrical connections per code requirements. Installed humidifier integration with new furnace system. Reconnected all ductwork and utilities to new equipment. Verified system operation using digital manifold gauges, confirming proper refrigerant pressures and temperatures. All equipment tested and operational upon completion.

# HVAC Service Report Responded to no cooling complaint on outdoor condensing unit. Upon arrival, found extensive debris accumulation around and on top of equipment, including dead leaves, dried vegetation, and organic matter restricting airflow. Observed visible rust and corrosion on capacitor housing and metal components indicating prolonged environmental exposure. Cleared all debris from unit exterior, base, and surrounding area. Inspected electrical connections and found wiring intact with proper terminations at contactor and capacitor. Cleaned interior cabinet surfaces of accumulated dirt and dust. Verified proper electrical operation of contactor and capacitor function. Unit restored to normal cooling operation after debris removal and cleaning.

Conducted on-site evaluation for HVAC system replacement at residential property. Assessed existing gas meter installation, utility connections, and electrical panel capacity to determine compatibility requirements for new equipment. Documented current system configuration including gas line routing, electrical service specifications showing dual AC circuits, and exterior mounting locations to provide accurate replacement estimate.

# HVAC Service Completed Responded to no cooling call on residential system over 10 years old. Arrived on-site during afternoon hours with ambient temperature at 89°F. Performed comprehensive diagnostic evaluation of heating and cooling system installed in basement utility area. System consists of gray metal forced-air furnace unit with vertical black cylindrical ductwork extending to ceiling. Conducted systematic troubleshooting to identify cause of cooling failure. Inspected all major components including compressor, condenser unit, refrigerant levels, electrical connections, and thermostat operation. Identified failed component preventing proper cooling operation. Completed necessary repairs to restore system functionality. Diagnostic fee waived with completion of repair work. Verified system operation and proper cooling performance before departure. Unit returned to normal operating condition with adequate airflow and temperature control restored.

Completed comprehensive air conditioning tune-up on outdoor condensing unit. Performed standard maintenance inspection, verified proper operation of fan motor and compressor, cleaned debris from exterior surfaces, and documented equipment condition with service photos showing unit positioned on grass pad with adequate clearance for airflow.

Completed comprehensive cooling maintenance tune-up on residential HVAC system as part of annual comfort club agreement. System was operating properly upon arrival and confirmed to be functioning correctly throughout inspection. Performed standard maintenance procedures including inspection of blower motor assembly, evaluation of heat exchanger coil condition, and electrical system diagnostics using digital multimeter to verify proper voltage readings at condenser unit. All components inspected and found to be in good working order with no repairs required at this time.

Responded to service call for non-operational AC system serving zones 4-6. Performed comprehensive assessment of existing HVAC equipment and thermostat controls, documented current system configuration including Honeywell Home thermostat and basement mechanical room layout with existing ductwork, electrical connections, and plumbing infrastructure. Provided complete replacement estimate for new equipment installation to restore cooling capacity to affected zones.

Conducted comprehensive evaluation of existing HVAC system including Evcon furnace and air handler unit for equipment replacement estimate. Assessed current system configuration, ductwork connections, condensate drainage lines, and overall installation condition to provide both single component air conditioning replacement option and complete system replacement quote. Documented equipment specifications, clearances, and existing infrastructure to prepare detailed proposal for customer consideration.

Responded to no cooling complaint on 10-year-old AC system. Upon arrival, performed diagnostic evaluation of outdoor condensing unit and electrical components. Removed service panel to inspect contactor, capacitor, and associated wiring connections. Verified power supply at exterior disconnect box and checked electrical connections for proper voltage and continuity. Inspected capacitor for signs of failure or degradation and tested contactor operation. Evaluated overall condition of aging unit including compressor functionality and refrigerant system integrity. Documented findings with photos of electrical components and disconnect box for service records. System required attention due to age-related wear on electrical components common in units exceeding 10-year service life.

Completed on-site assessment for mini-split heat pump installation in residential property. Evaluated two interior locations including living room with stone fireplace and adjacent room with through-wall AC unit to determine optimal placement for 10,000-12,000 BTU ductless mini-split system. Documented existing HVAC conditions, wall construction, electrical access points, and recommended indoor head unit mounting locations with consideration for airflow distribution and aesthetic integration with current décor.

Completed comprehensive AC/furnace tune-up on residential HVAC system. Performed standard maintenance inspection of outdoor condensing unit, verified proper operation of all components, and documented equipment condition with photographs showing unit positioned on concrete pad against building exterior with refrigerant lines properly secured.

Responded to service call for air conditioning unit that was running continuously without cycling off. Upon inspection, diagnosed failed contactor relay preventing the system from properly shutting down. Removed defective contactor assembly and installed replacement relay component. Verified proper system operation with normal cycling restored and unit shutting off as designed.

Completed installation of 70,000 BTU furnace system in residential basement utility room, including all mechanical and electrical connections. Installed new air handler unit with galvanized metal housing, connected white PVC venting system for proper exhaust and intake, and reconnected all existing ductwork to new equipment. Verified all electrical connections to code, tested system operation, and confirmed proper airflow throughout the home.