Trusted Heating, Cooling, Electrical & Water Heater Services in Flat Rock, MI

Responded to no cooling complaint on Goodman AC unit. Upon arrival, performed diagnostic inspection of outdoor condensing unit. Visually inspected equipment exterior, verified manufacturer labeling and unit specifications. Documented current condition of equipment showing normal environmental weathering. Checked electrical connections and observed wiring configuration at outdoor unit. Unit assessed as part of agreement visit maintenance protocol.

Completed preventive maintenance agreement visit for club AC8-12 system. Performed comprehensive inspection of electrical components and wiring connections within equipment panel, verified proper wire management and component labeling, and documented system configuration with photos for service records.

Successfully completed installation of 3-ton air conditioning system with matching evaporator coil. Installed outdoor condensing unit at rear of property on prepared pad with proper clearances from building foundation. Ran and connected copper refrigerant lines from outdoor unit to indoor coil using proper brazing techniques and flare fittings. Mounted evaporator coil above existing Lennox furnace in basement utility area, integrating with existing ductwork via metal plenum. Made all necessary electrical connections to outdoor unit and indoor components per manufacturer specifications and local electrical codes. Completed mechanical connections including refrigerant line sets with appropriate insulation. Evacuated system to remove moisture and non-condensables, then charged system with proper refrigerant type and quantity per manufacturer specifications. System startup performed with digital pressure gauges confirming operating pressures of 37.1 PSI on suction side, indicating proper r

Completed on-site assessment for water heater replacement in residential property where occupant has been without hot water for approximately one month. Evaluated existing ComfortMaster energy water heater installed in recessed wall alcove, documented current plumbing connections including flexible supply lines and metal piping at top of unit, and assessed HVAC system integration with return air vent and equipment cabinet. Provided detailed estimate for replacement unit with availability projected within 4-6 weeks, and discussed financing options to facilitate installation.

Conducted comprehensive site assessment for air conditioning system replacement at residential property. Evaluated existing electrical panel capacity and outdoor installation location to prepare updated equipment specifications and installation requirements for complete AC system replacement.

Responded to emergency no-cooling call on thirteen-year-old air conditioning system. Upon inspection, found severely corroded contactor with deteriorated terminals and significant environmental damage affecting electrical connections. Documented existing capacitor and wiring configuration showing multiple compromised connection points due to age and exposure. System components displayed extensive oxidation, grime accumulation, and general wear consistent with unit age, requiring immediate attention to restore cooling operation.

Completed preventive maintenance inspection on air conditioning system as part of club AC10-2 agreement visit. Performed electrical diagnostics using digital multimeter, measuring amperage draw of 0.65A and conducting voltage tests throughout the system. Inspected and tested all electrical components including capacitor and control wiring connections to verify proper operation and system performance.

Completed preventive maintenance agreement visit for Club AC8-12 service on air conditioning system. Performed comprehensive electrical diagnostics using digital multimeter, recording amperage draw of 8.32 amps and supply voltage of 92.9 volts to verify proper system operation and component performance within manufacturer specifications.

Conducted comprehensive assessment of existing Powerflex water heater installation in basement utility area for replacement estimate. Documented current unit specifications, connections including copper supply lines with shutoff valve, electrical service, and PVC venting system configuration. Evaluated surrounding infrastructure including spray foam insulation coverage, available clearances, and access for equipment removal and installation.

Completed preventive maintenance agreement visit for Club AC8-12 service on air conditioning system. Performed comprehensive electrical diagnostics using clamp meter to verify amperage draw at 71.5 amps, indicating proper compressor operation within manufacturer specifications. Utilized digital manifold gauge set to measure refrigerant pressures and temperatures across the system, confirming optimal superheat and subcooling values. Inspected CoreSense Diagnostics module and all electrical connections, capacitor, and wiring harnesses for proper operation and secure terminations. All system parameters tested within normal operating range with no deficiencies noted.

Completed comprehensive cooling system tune-up and inspection on residential HVAC unit that had not been serviced in three years. Replaced heavily soiled air filter showing significant dust and debris accumulation, inspected electrical connections and control board wiring, and verified proper operation of all system components. System found to be operating within normal parameters with no immediate repairs required.

# HVAC Maintenance - Agreement Visit AC&SI Completed routine preventative maintenance inspection under Club AC12-4 agreement. Performed comprehensive system evaluation including visual inspection of refrigerant lines and electrical measurements. Documented existing corrosion on penetration pipe requiring future attention. Obtained amperage and voltage readings using calibrated test equipment, confirming system operating within normal parameters at 0.65A. All safety checks completed satisfactorily.

Completed scheduled AC Club maintenance visit during afternoon service window. Performed routine inspection and cleaning of indoor cooling system components, including removal and servicing of air filter assembly. System operational and cooling function restored to normal parameters.

Responded to no-heat condition on tankless water heater unit. Upon inspection, accessed and evaluated the internal blower assembly and heat exchanger components. Examined the blower wheel housing and verified proper clearances of the centrifugal fan blades within the volute chamber. Documented equipment model number GMVM961005DXAA and serial number for service records. Inspected refrigerant lines, copper piping connections, and insulated tubing for proper installation and potential restrictions. Assessed the overall condition of the unit's internal components, noting normal wear patterns on metal surfaces. Unit was evaluated for operational readiness and proper airflow through the heat exchanger assembly.

Completed scheduled AC tune-up maintenance on Lennox 13ACX outdoor condensing unit. Performed comprehensive system inspection, verified refrigerant charge, checked electrical connections, and documented unit specifications. All components operating within normal parameters with no issues identified.

Completed scheduled preventive maintenance visit for Club AC8-12 agreement. Performed comprehensive inspection of air conditioning system and safety components. Verified proper operation of all equipment, checked refrigerant levels, inspected ductwork and air handler components, and confirmed sensor functionality with blue LED indicator showing normal status. All systems operating within manufacturer specifications with no deficiencies noted.

Completed full HVAC system installation including a 90,000 BTU furnace and 4-ton air conditioning unit positioned on the right side of the property. Installed 3-inch exhaust and intake venting for proper combustion air and flue gas evacuation. Performed all mechanical and electrical connections, reconnected refrigerant lines, and verified system pressures and temperatures using calibration-grade digital instruments. All equipment tested and operational upon completion.

Completed scheduled AC Club maintenance visit on Goodman R9X130610A cooling system. Performed comprehensive inspection of indoor air handler unit and outdoor condensing unit, including electrical testing with digital multimeter to verify proper voltage and amperage readings. Inspected refrigerant lines, condensate drainage system, and ductwork connections for proper operation and signs of wear. All components found to be functioning within normal parameters with no immediate service needs identified.

# HVAC System Estimate - Replacement Assessment Conducted comprehensive assessment of existing Lennox furnace system located in basement utility area for replacement estimate. Evaluated current equipment configuration including furnace unit, metal ductwork system, and air handler components. Documented existing installation showing furnace with ventilation louvers, manufacturer specification labels, and connected galvanized steel ductwork extending vertically with horizontal connections. Noted flexible black ductwork at ceiling level and metallic elbow duct connections. Photographed complete system layout including equipment positioning against wall framing, PVC drainage piping, and floor drain location for replacement planning purposes. Provided detailed system estimate for 8-10 SEER replacement equipment options.

Installed ground fault circuit interrupter (GFI) outlet with weatherproof cover on exterior wall. Ran gray PVC conduit vertically along white vinyl siding to protect wiring from environmental exposure. Mounted outdoor-rated electrical box with clear hinged weatherproof cover to allow access while maintaining protection from moisture and weather elements. Verified proper grounding and tested GFI functionality to ensure compliance with electrical safety standards for outdoor receptacles.